- 您现在的位置：买卖IC网 > Sheet目录886 > TMK063CK1R5DPGF (Taiyo Yuden)CAP CER 1.5PF 25V C0K 0201
（2）Examples of good and bad solder application
Item
Not recommended
Lead wire of component
Recommended
Solder-resist
Mixed mounting of SMD and
leaded components
Chassis
Component placement close to
the chassis
Solder (for grounding)
Electrode pattern
Lead wire of component
Solder-resist
Hand-soldering of leaded
Soldering iron
Solder-resist
components near mounted
components
Solder-resist
Horizontal component
placement
◆Pattern configurations （Capacitor layout on PCBs）
1-1. The following is examples of good and bad capacitor layouts ; capacitors shall be located to minimize any
stresses from board warp or deflection.
possible mechanical
Items
Deflection of board
Not recommended
Recommended
Place the product at a right
angle to the direction of the
anticipated mechanical
stress.
1-2. The amount of mechanical stresses given will vary depending on capacitor layout. Please refer to diagram below.
E
D
Perforation
C
A
Slit
B
Magnitude of stress
A＞B＝C＞D＞E
1-3. When PCB is split, the amount of mechanical stress on the capacitors can vary according to the method used. The following methods
are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, please consider the PCB,
split methods as well as chip location.
3. Mounting
◆Adjustment of mounting machine
1. When capacitors are mounted on PCB, excessive impact load shall not be imposed on them.
2. Maintenance and inspection of mounting machines shall be conducted periodically.
Precautions
◆Selection of Adhesives
1. When chips are attached on PCBs with adhesives prior to soldering, it may cause capacitor characteristics degradation unless the
following factors are appropriately checked : size of land patterns, type of adhesive, amount applied, hardening temperature and
hardening period. Therefore, please contact us for further information.
? This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E02R01
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
TO1608-102M
INDUCTOR 1000UH 70MA 1608 +-20%
TO3316-102M
INDUCTOR 1000UH 300MA 3316 +-20%
TPL1183427-722J-720N
COIL TRANSPONDER 7.2MH SMD
TS5022-102M
INDUCTOR 1000UH .55A SHLD 5022
TVX2A220MAD
CAP ALUM 22UF 100V 20% AXIAL
TWR-5/1000-12/210-D12A-C
CONV DC/DC TRI OUT 5,12,-12V
TWR-5/1500-12/250-D48A-C
CONV DC/DC TRI OUT 5,12,-12V
TWR-5/3000-15/500-D48A-C
CONV DC/DC TRI OUT 5,15,-15V
相关代理商/技术参数
TMK10024
制造商:TE Connectivity 功能描述: 制造商:TE Connectivity / Schrack Brand 功能描述:
TMK105 BJ103KV-F
制造商:TAIYO YUDEN 功能描述:Ceramic Multilayer Capacitor
TMK10524
制造商:TE Connectivity 功能描述: 制造商:TE Connectivity / Schrack Brand 功能描述:
TMK105ABJ474KV-F
功能描述:CAP CER 0.47UF 25V X5R 0402 制造商:taiyo yuden 系列:M 包装:剪切带（CT） 零件状态:在售 电容:0.47μF 容差:±10% 电压 - 额定:25V 温度系数:X5R 工作温度:-55°C ~ 85°C 特性:- 等级:- 应用:通用 安装类型:表面贴装，MLCC 封装/外壳:0402（1005 公制） 大小/尺寸:0.039" 长 x 0.020" 宽（1.00mm x 0.50mm） 高度 - 安装（最大值）:- 厚度（最大值）:0.022"（0.55mm） 引线间距:- 引线形式:- 标准包装:1
TMK105ABJ474KVHF
功能描述:0.47μF 25V 陶瓷电容器 X5R 0402（1005 公制） 0.039" 长 x 0.020" 宽（1.00mm x 0.50mm） 制造商:taiyo yuden 系列:M 包装:剪切带（CT） 零件状态:有效 电容:0.47μF 容差:±10% 电压 - 额定:25V 温度系数:X5R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 85°C 应用:汽车级 等级:AEC-Q200 封装/外壳:0402（1005 公制） 大小/尺寸:0.039" 长 x 0.020" 宽（1.00mm x 0.50mm） 高度 - 安装（最大值）:- 厚度（最大值）:0.024"（0.60mm） 引线间距:- 特性:- 引线形式:- 标准包装:1
TMK105AC6105KV-F
功能描述:1μF ±10% 25V 陶瓷电容器 X6S 0402（1005 公制） 制造商:taiyo yuden 系列:M 包装:剪切带（CT） 零件状态:在售 电容:1μF 容差:±10% 电压 - 额定:25V 温度系数:X6S 工作温度:-55°C ~ 105°C 特性:- 等级:- 应用:SMPS 过滤器 故障率:- 安装类型:表面贴装，MLCC 封装/外壳:0402（1005 公制） 大小/尺寸:0.039" 长 x 0.020" 宽（1.00mm x 0.50mm） 高度 - 安装（最大值）:- 厚度（最大值）:0.024"（0.60mm） 引线间距:- 引线形式:- 标准包装:1
TMK105AC6105MV-F
功能描述:1μF ±20% 25V 陶瓷电容器 X6S 0402（1005 公制） 制造商:taiyo yuden 系列:M 包装:剪切带（CT） 零件状态:在售 电容:1μF 容差:±20% 电压 - 额定:25V 温度系数:X6S 工作温度:-55°C ~ 105°C 特性:- 等级:- 应用:SMPS 过滤器 故障率:- 安装类型:表面贴装，MLCC 封装/外壳:0402（1005 公制） 大小/尺寸:0.039" 长 x 0.020" 宽（1.00mm x 0.50mm） 高度 - 安装（最大值）:- 厚度（最大值）:0.024"（0.60mm） 引线间距:- 引线形式:- 标准包装:1
TMK105B7103KV-F
功能描述:多层陶瓷电容器MLCC - SMD/SMT CAP MLCC 0402 25V X7R 0.01uF 10%
RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel